ULTIMATE STARTER KIT FOR ARDUINO MEGA2560, ADEEPT, ADA010

Product details:

This is a Ultimate Starter Leaning Kit for Arduino MEGA 2560, wich contains more than 50 kinds of different electronic components and more than 180 components are included.

With this kit you are able to do more experiment, get your ideas into real action without the restriction of hardware and software.

Lessons:

• About Arduino 

1. Lesson 1 Blinking LED 
2. Lesson 2 Active Buzzer 
3. Lesson 3 Controlling an LED with a button
4. Lesson 4 Controlling Relay 
5. Lesson 5 Serial Port 
6. Lesson 6 LED Flowing Lights 
7. Lesson 7 LED bar graph display 
8. Lesson 8 Breathing LED 
9. Lesson 9 Controlling a RGB LED by PWM 
10. Lesson 10 Play the Music 
11. Lesson 11 LCD1602 display 
12. Lesson 12 A Simple Voltmeter    
13. Lesson 13 7-segment display 
14. Lesson 14 A simple counter 
15. Lesson 15 Controlling Servo motor 
16. Lesson 16 Using a thermistor to measure the temperature 
17. Lesson 17 IR Remoter Controller 
18. Lesson 18 Temperature & humidity sensor DHT-11
19. Lesson 19 ultrasonic distance sensor 
20. Lesson 20 3-axis Accelerometer—ADXL345 
21. Lesson 21 4x4 matrix keyboard 
22. Lesson 22 Controlling DC motor 
23. Lesson 23 Joy stick 
24. Lesson 24 Tilt Switch 
25. Lesson 25 Dot-matrix display 
26. Lesson 26 Controlling Stepper Motor 
27. Lesson 27 Photoresistor 
28. Lesson 28 Automatically Tracking Light Source 
29. Lesson 29 Frequency meter 
30. Lesson 30 Intrusion Detection based on the PIR 
31. Lesson 31 Control a relay with IR remoter controller 
32. Lesson 32 Control a RGB LED with IR remoter controller 
33. Lesson 33 control a stepper motor with IR remoter controller

Package include:

• 1x  Adeept MEGA 2560 Board(Arduino MEGA 2560 R3) This is not original Arduino Board!
• 1x  MEGA 2560 Development Expansion Board 
• 1x  Mini Breadboard 
• 1x  ADXL345 Acceleration Sensor 
• 1x  Ultrasonic Distance Sensor 
• 1x  IR Receiver HX1838 
• 1x  Remote Controller 
• 1x  PS2 Joystick Module 
• 1x  Relay 
• 1x  Stepper Motor 
• 1x  ULN2003 Stepper Motor Driver Module 
• 1x  DHT-11 Temperature & Humidity Sensor 
• 1x  LED Bar Graph 
• 1x  Active Buzzer 
• 1x  Passive Buzzer 
• 1x  PIR Movement Sensor 
• 1x  Servo 
• 2x  Analog Temperature Sensor(Thermistor) 
• 1x  Breadboard Power Supply Module 
• 1x  4*4 Matrix Keyboard 
• 1x  DC Motor 
• 1x  L9110 DC Motor Driver 
• 1x  LCD1602 
• 1x  Dot-matrix Display 
• 1x  7-segment Display 
• 1x  4-bit 7-segment Display 
• 1x  NE555 Timer                                
• 2x  74HC595 
• 2x  Light Sensor (Photoresistor) 
• 2x  Tilt Switch 
• 2x  Switch 
• 1x  RGB LED 
• 8x  Red LED 
• 4x  Green LED 
• 4x  Yellow LED 
• 4x  Blue LED 
• 16x Resistor(220Ω) 
• 10x Resistor(1kΩ) 
• 10x Resistor(10kΩ) 
• 2x  Potentiometer(10KΩ) 
• 5x  Capacitor(104) 
• 4x  Capacitor(10uF) 
• 4x  Button(large) 
• 8x  Button(small) 
• 1x  Button Cap(red) 
• 1x  Button Cap(white) 
• 2x  Button Cap(blue) 
• 4x  NPN Transistor(8050) 
• 4x  PNP Transistor(8550) 
• 4x  1N4148 Diode 
• 4x  1N4001 Diode 
• 1x  9V Battery Clip 
• 1x  Breadboard 
• 1x  USB Cable 
• 40x Male to Male Jumper Wires 
• 20x Male to Female Jumper Wires 
• 20x Female to Female Jumper Wires 
• 1x  Header(40pin) 
• 1x  Band Resistor Card 
• 1x  Project Box 

PDF: Arduino_Lessons_ADA010.pdf